Saturday, June 12, 2010

Military Miniatures in Review No.17


The M6 antitank gun was derived from the 3-inch gun carriage Ml. Near the end of 1942, the United States took a 3-inch anti-aircraft tube and mated it with the 105mm howitzer carriage. These guns were used in all theaters of war, although they were best known for their use in and around Bastone during the Battle of the Bulge. They were quite cumbersome, but proved to be very effective. This gun was also modified to fit the 3-inch GMC, (Gun Motor Carriage) M10 Tank Destroyer. KMC's conversion is very impressive, as is most of their product line. Their delicate resin castings make me nervous every time I handle them. 1 am always impressed with how thin and to scale some of these pieces reallv are. This does not mean that this conversion was a breeze. There were some minor annoyances, hut I think this article and the accompanying photos will help clear those up. You will also need one Italeri 105mm howitzer M101 to mate with KMC's M6 conversion. I don't know how Italeri's 105 howitzer kit slipped past me through the years. After I looked over the details of the Italeri sprues I was truly impressed. This is one nice kit, right out of the box.

Download from (hotfile.com)

Minitracks No.6


This tank was created through a common work, from July to November 1916, by the famous général Estienne and Louis Renault, a well-known manufacturer. The Général's conception was to provide escort to medium tanks and the infantry with great quantities of 'infantrymen under armour' and fitted with MGs, that could harass the enemy in any terrain. To achieve that, the tank had to be small, with just a two man crew (one driving, one manning the armament). To optimize the inside space, a crew compartment was created, separated from the rear located engine. The engine as itself a car one, saving much time in research and factory conversion, as it was already on the assembly lanes. The suspension was quite different from previous French offerings as it was enveloping and not situated under the hull as usual. The sprocket was at rear, and the wooden idler had a great diameter to easily overcome obstacles. An unditching tail was added to improve the trench crossing ability. There was only one MG, but housed in a fully revolving turret. It was later even possible to mount a short 37mm gun, modified to be operable by a lone crew.

Download from (hotfile.com)

Wing Masters No.37


En 1942-1943 North American développe des versions d'assaut du Mitchell, les B-25G et H équipés d'un canon de 75 mm moins efficace qu'on ne l'espérait. Avec le B-25J, la firme revient à la formule du bombardier moyen en greffant un habitacle vitré, semblable à celui des modèles C et D, à une cellule identique à celle d'un B-25H. Les livraisons suivent l'envol du premier exemplaire le 14 décembre 1943. Une version d'assaut avec huit mitrailleuses de 12,7 mm dans une proue carénée est produite à 800 unités, un kit de modification est livré aux unités équipées de bombardiers; l'armement est exceptionnel pour un avion de cette catégorie. En août 1945 la production cesse du jour au lendemain: 72 engins terminés ne sont pas pris en compte.

Download from (hotfile.com)

Modelismo Aplicado - Vehiculos Militares


Básicamente lodos los vehi culos militares tienen un proceso de montaje muy similar. Al abrir la caja, el principiante se encuentra con unas instrucciones más o menos claras y unas ban dejas o grapas donde vienen sujetas las piezas. El primer problema que aparece es cómo separarlas limpiamente, pues en ningún caso deben arrancarse con la mano, girando la pieza sobre sí misma, pues se corre el riesgo de estropearla al desgarrar parte de ella, hay varios sis temas para llevar a cabo ade cuadamente este proceso: se puede utilizar una cuchilla curva que corte poco a poco, aunque lo más conveniente son unas tijeri tas de punta bien afiladas o, como máximo, una tenaza de corte especial. Una vez desprendida la pieza, descubrimos un trocito sobrante proveniente de la unión, como una verruga de plástico, que se elimina cortándolo con una cuchilla. También con frecuen da. aunque la pieza esté bien inyectada, puede aparecer una ligera linea de plástico que sobre sale en el punto concreto de unión de los moldes, que, depen diendo de dónde esté situada la pieza en la maqueta, puede verse o quedar oculto.

Download from (hotfile.com)